Cable Blowing Lubricant UP-S-LUB-100XL
Cable Blowing Lubricant UP-S-LUB-100XL is a water-based lubricant developed for mini and micro cable installation in fiber ducts. It helps reduce friction during cable jetting and pre-lubrication, leaves a light film on the inner duct surface, and supports smoother installation performance without creating a sticky glue effect.
Designed for cable and duct pre-lubrication, this fiber duct lubricant can be used before jetting, during installation with an oil dispenser, or directly on the cable when application conditions require controlled surface lubrication. For installers working with compact ducts, tight bends, or long runs, it gives a cleaner and more practical handling profile than generic lubricants that were never meant for fiber work in the first place.
Why Choose Cable Blowing Lubricant UP-S-LUB-100XL
Built for fiber duct installation
This cable jetting lubricant is designed for fiber optic installation work, not for generic industrial sliding. That matters when you want stable cable movement inside small ducts rather than unpredictable residue.
Water-based and easy to handle
The formula is a water-based emulsion of polymers with a semi-liquid, low-viscosity structure. It spreads easily, coats the inner surface effectively, and stays practical for field use.
Helps lower friction fast
By reducing friction between cable and duct wall, the product supports smoother cable insertion, more stable pushing behavior, and cleaner pre-lubrication in mini and micro duct environments.
Designed for small internal duct diameters
UP-S-LUB-100XL is positioned for compact fiber duct applications where installation control matters more than dumping random lubricant into the route and hoping physics feels cooperative that day.
Where This Fiber Duct Lubricant Fits Best
Mini and micro cable installation
Suitable for mini and micro cable installation processes where controlled lubrication helps the cable move more efficiently through the duct.
Duct pre-lubrication before jetting
It can be introduced into the duct first, then distributed along the route to reduce wall friction before the actual cable blowing process begins.
Use with blowing machine oil dispenser
The product is also suitable for systems using an oil dispenser to lubricate the fiber during the pushing phase.
Before or after machine entry point
Depending on the machine layout and wheel material, lubrication can be applied before or after the cable enters the blowing unit.
Cable Blowing Lubricant UP-S-LUB-100XL Usage Quantity
The table below shows the suggested quantity for a 1000 m installation. Actual consumption may vary depending on duct condition, route length, bends, cleanliness, and installation difficulty.
| Internal Duct Diameter | Suggested Product Quantity | Indicative Fill Length |
|---|---|---|
| 4 mm | 5 mm | ≈ 30 cm |
| 8 mm | 10 mm | ≈ 20 cm |
| 12 mm | 15 mm | ≈ 15 cm |
How to Use Cable Blowing Lubricant UP-S-LUB-100XL
- Shake the bottle before use. This helps the lubricant maintain a more even consistency before application.
- Introduce the product into the duct. Apply the required quantity based on the duct size and route condition.
- Pre-lubricate the inside of the duct. Push a small sponge through the duct using compressed air so the lubricant spreads more evenly along the route.
- Proceed with cable blowing. The product can also be used with oil-dispenser-supported blowing systems during the pushing phase.
- Adjust to machine setup. Lubrication can be applied before or after the machine depending on whether the unit uses iron wheels or rubber wheels.
Practical application note
For fiber blowing lines with small internal diameters, consistent distribution matters more than raw volume. A properly spread thin film is usually more useful than excess product concentrated at the duct entry.
This is where many installations go wrong: too much lubricant at one point, too little across the route, then everyone blames the cable.
Technical Specification of Cable Blowing Lubricant UP-S-LUB-100XL
| Product Consistency | Semi liquid |
|---|---|
| Aspect | White liquid, tiny viscosity |
| Odor | Characteristic |
| Viscosity | 30 sec. Ford cup, diameter 4 mm at 20°C |
| Specific Gravity | 1.030 ± 0.03 g/cm³ |
| pH | 7.5 ± 0.5 |
| Inflammability | Nonflammable |
| Recommended Temperature Range | 0°C to +70°C |
| Cable Installation Method | Blowing machine |
| Application | Cable threading / cable blowing support |
| Installation Type | Industrial |
| Recommended Internal Duct Size | From 4 mm to 12 mm |
Packaging Options
Cable Blowing Lubricant UP-S-LUB-100XL is available in bottle and tank formats for different installation scales, from routine field use to larger-volume project preparation.
| Product Code | Wrapping / Packaging |
|---|---|
| UP-VSLUB100XL05-12 | Bottle 500 gr / box 12 pc |
| UP-VSLUB100XL1-15 | Bottle 1 kg / box 15 pc |
| UP-VSLUB100XL1-12 | Bottle 1 kg / box 12 pc |
| UP-VSLUB100XL1-06 | Bottle 1 kg / box 6 pc |
| UP-VSLUB100XL5 | Tank 5 kg / 1 pc |
| UP-VSLUB100XL10 | Tank 10 kg / 1 pc |
| UP-VSLUB100XL20 | Tank 20 kg / 1 pc |
| UP-VSLUB100XL25 | Tank 25 kg / 1 pc |
FAQ
What is Cable Blowing Lubricant UP-S-LUB-100XL used for?
It is used for cable and duct pre-lubrication in fiber optic installation, especially for mini and micro cable blowing applications where lower friction improves handling inside the duct.
Is this product suitable for mini and micro cable installation?
Yes. The product is designed for mini and micro cable applications and is recommended for internal duct diameters from 4 mm to 12 mm.
Can it be used with a cable blowing machine oil dispenser?
Yes. The datasheet indicates that it is also suitable for blowing machines equipped with an oil dispenser to lubricate the fiber during pushing.
Does it leave sticky residue inside the duct?
No. It is formulated to leave a very light lubricating film rather than creating a glue effect on the cable or internal duct surface.
Is UP-S-LUB-100XL flammable?
No. The product is specified as nonflammable.